ESD electronic CAN-USB/2 Handbuch

CAN-USB/2USB 2.0-CAN-InterfaceHardware Manualto Product C.2066.xxCAN-USB/2Hardware Manual • Doc. No.: C.2066.21 / Rev. 1.4Page 1 of 25

Technical Data4. Technical Data4.1 General Technical DataTemperature range0...50°C ambient temperatureHumidity 90 %, non-condensingPower supplyvia USB

Technical Data4.3 CAN InterfaceNumber of CAN interfaces1CAN protocol ISO 11898-1 (11 and 29 bit CAN identifier are supported)Physical LayerCAN High Sp

Connector Assignments5. Connector Assignments5.1 CAN Interface at DSUB9 ConnectorDevice connector: RJ45 socket, 8-pinPin Position:Pin Assignment:Signa

Connector Assignments5.2 USB SocketNote:The module may only be operated at USB nets with USB interface version numbers ≥ 1.1-interface! Using versions

Correctly Wiring Electrically Isolated CAN Networks6. Correctly Wiring Electrically Isolated CAN NetworksFor the CAN wiring all applicable rules and r

Correctly Wiring Electrically Isolated CAN Networks6.1.2 Cabling● for devices which have only one CAN connector per net use T-connector and stub (shor

Correctly Wiring Electrically Isolated CAN Networks6.2 Heavy Industrial Environment (Double Twisted Pair Cable)6.2.1 General RulesThe following genera

Correctly Wiring Electrically Isolated CAN Networks6.2.2 Device Cabling● To connect CAN devices which are equipped with one CAN co

Correctly Wiring Electrically Isolated CAN Networks6.3 Electrical Grounding● CAN_GND has to be connected between the CAN devices, because esd CAN devi

Correctly Wiring Electrically Isolated CAN Networks6.5 Examples for CAN Cables6.5.1 Cable for Light Industrial Environment Applications (Two-Wire)Manu

N O T EThe information in this document has been carefully checked and is believed to be entirely reliable. esd makes no warranty of any kind with reg

CAN Troubleshooting Guide7. CAN Troubleshooting GuideThe CAN Troubleshooting Guide is a guide to find and eliminate the most frequent hardware-error c

CAN Troubleshooting Guide7.2 Electrical GroundingThe CAN_GND of the CAN network has to be connected to the functional earth potential (FE) at only one

CAN Troubleshooting GuideNormally the voltage should be between 2.0 V and 4.0 V. If it is lower than 2.0 V or higher than 4.0 V, it is possible that o

Declaration of Conformity8. Declaration of ConformityPage 24 of 25Hardware Manual • Doc. No.: C.2066.21 / Rev. 1.4CAN-USB/2

Order Information9. Order InformationType Properties Order No.CAN-USB/2 1 x CAN 2.0A/B, ISO 11898, USB 2.0 C.2066.02* includes CAN layer 2 software dr

Document file:I:\Texte\Doku\MANUALS\CAN\CAN-USB-2\Englisch\CAN-USB2_Hardware_en_14.odtDate of print: 2013-03-06Document type number:DOC0800PCB version

Safety Instructions● When working with CAN-USB/2 follow the instructions below and read the manual carefully to protect yourself from injury and the C

Table of contents1. Overview...

Overview1. OverviewFigure 1: Block-circuit diagram of CAN-USB/2 moduleThe CAN-USB/2 module is an intelligent CAN interface with an ARM7 micro control

Case View with LED and Connector Description2. Case View with LED and Connector DescriptionFigure 2: PCB top viewFigure 3: USB InterfacePage 8 of 25

Case View with LED and Connector Description2.1 LED-DisplaysLEDNAME Number StatusDescriptionUSB LED300DonUSB module is enumerated(a node-ID is assigne

Hardware Installation 3. Hardware Installation To put the CAN-USB/2 into operation, please follow the installation notes.Step Proceduresee pageRead